Hyperdesmo C-LV

Hyperdesmo C-LV is a single-component, low-viscosity, polyurethane-based cast elastic membrane for waterproofing and protective applications. It cures with atmospheric moisture and forms a monolithic, seamless waterproofing membrane with full-surface adhesion. It contains a small amount of solvent, specifically xylene, and does not require additional dilution before application.

Hyperdesmo C-LV is used for waterproofing and protecting:

  • Roofs and flat roofs
  • Balconies
  • Bathrooms
  • Asphalt roofing sheets
  • EPDM membranes
  • Elenit and sheet metal
  • Drywall and cement board

  • One-component polyurethane sealant
  • Low viscosity
  • Requires no additional dilution
  • Forms a seamless film
  • High adhesion to the application surface
  • High resistance to ultraviolet radiation
  • Water vapor permeability
  • Resistance to hydrolysis and microorganisms
  • Fills microcracks
  • High elasticity
  • Allows for bonding of covering materials, such as tiles, to the film when using the appropriate application system
  • ETA-04/0082 Certification

  • Type: Single-component polyurethane waterproofing membrane
  • Drying time at 25°C and 55% RH: approximately 6 hours
  • Recoating time: 6–24 hours
  • Operating temperature of the membrane: -40°C to +90°C
  • Elongation at 23°C: >500%
  • Adhesion to concrete: >2 N/mm
  • Certification: ETA-04/0082
  • Minimum safe service life category: W3, 25 years

The minimum total coverage is 1.5–1.8 kg/m².

First coat: 0.8–0.9 kg/m²

Second coat: 0.7–0.9 kg/m²

Spray application: 0.8 kg/m² per coat

Viscosity at 25°C: 2,000–3,500 cP

Specific gravity at 20°C: 1.35–1.45 g/cm³

White

1 kg, 6 kg, 15 kg, 25 kg

In its original packaging, and provided it remains in unopened containers, it has a shelf life of at least 12 months from the date of manufacture when stored at a temperature of 5°C–25°C in a dry place. Once opened, it must be consumed immediately. Keep out of reach of children.

It can be applied to properly prepared surfaces such as:

  • Reinforced or unreinforced concrete
  • Gravel mosaic
  • Roofing slabs
  • Durable acrylic coatings
  • Asphalt coatings
  • Wooden surfaces
  • Oxidized metals
  • Galvanized steel and aluminum, using a suitable primer

Before application:

  • Remove loose material
  • Clean the surface of dust
  • Remove salts, oils, and plant matter
  • Sand and clean loose surfaces
  • Roughen glossy surfaces or prime them with Aquadur or Primer-T
  • For unarmored applications, severe cracks are repaired prior to the final coat using a suitable polyurethane mastic

Application Method

Hyperdesmo C-LV is mixed by hand or with a low-speed mixer for approximately 2–3 minutes.

It can be applied using:

  • A roller
  • A brush
  • Airless spray at 200–250 bar
  • Coats are applied sequentially at intervals of 6–24 hours, depending on weather conditions

When to Use Hyperdesmo Ady-E or ADY 500

When Hyperdesmo C-LV is used in a dark shade and the surface is to remain exposed, a thin coat of Hyperdesmo Ady-E is then applied. This requirement specifically applies to exposed applications in dark shades.

For white shades, apply ADY 500

Application Restrictions

Hyperdesmo C-LV is not recommended for:

  • Surfaces with low cohesion
  • Waterproofing pool surfaces that are in direct contact with chemically treated water

FAQ about Hyperdesmo C-LV

Brands